# Whirlpool front-load washers and Maytag washers error codes | Costolio URL: https://costolio.com/home/appliances/whirlpool/whirlpool-front-load-washers/ Updated: 2026-11-02 # Whirlpool front-load washers and Maytag washers error codes 21 washer error codes for Whirlpool front-load washers, what each one means and what to try, paraphrased from Whirlpool's own sources. Codes vary by model, so confirm in your own manual. ## All codes - [LOC / LC](https://costolio.com#loc-lc) Control Lock is on, so the buttons will not respond. - [dET](https://costolio.com#det) Detergent cartridge not detected in the dispenser (select models). - [Int](https://costolio.com#int) The cycle was paused or canceled; the washer may spin and drain for 20 to 30 minutes. - [rL / F34](https://costolio.com#rl-f34) Items were found in the drum during the Clean Washer cycle. - [Sud / Sd](https://costolio.com#sud-sd) Too many suds; the washer adds rinse time to break them down. - [F5 E2](https://costolio.com#f5-e2) The door is not locking. - [F7 E1](https://costolio.com#f7-e1) The motor cannot reach the right speed. - [F8 E1 / LO FL](https://costolio.com#f8-e1-lo-fl) The washer is getting too little water. - [F8 E2](https://costolio.com#f8-e2) Problem with the dispenser system (select models). - [F9 E1](https://costolio.com#f9-e1) Draining is taking longer than expected (usually over 8 minutes). - [Other F# E#](https://costolio.com#other-f-e) Any other F/E fault code. - [HC](https://costolio.com#hc) The hot and cold inlet hoses are reversed. - [LdL](https://costolio.com#ldl) The lid will not lock. - [LdU](https://costolio.com#ldu) Objects on the washer lid are preventing it from unlocking. - [LF / Lo FL / F8 E1](https://costolio.com#lf-lo-fl-f8-e1) The washer is taking too long to fill. - [lid](https://costolio.com#lid) The lid was left open. - [Ofb](https://costolio.com#ofb) The load is out of balance and the washer is trying to correct it. - [OL](https://costolio.com#ol) The load is too large; the washer drained the water. - [PF](https://costolio.com#pf) A power failure interrupted the cycle. - [Sud](https://costolio.com#sud) Too many suds in the washer. - [F# E# / F##](https://costolio.com#f-e-f) A system error code. ## LOC / LC What it means: Control Lock is on, so the buttons will not respond. You can usually fix this yourself. ### What to try - Press the Control Lock button (on some models press and hold it). - Your Owner's Manual shows which button turns Control Lock on and off on older models. Source: [Error Codes in Front Load Washers (Whirlpool Product Help)](https://producthelp.whirlpool.com/Laundry/Washers/Product_Info/Washer_Product_Assistance/Error_Codes_in_Front_Load_Washers) (checked 2026-11-02) ## dET What it means: Detergent cartridge not detected in the dispenser (select models). You can usually fix this yourself. ### What to try - If you use single-load doses of detergent, you can ignore it. - Otherwise make sure the cartridge is inserted correctly and the dispenser drawer is shut completely. Source: [Error Codes in Front Load Washers (Whirlpool Product Help)](https://producthelp.whirlpool.com/Laundry/Washers/Product_Info/Washer_Product_Assistance/Error_Codes_in_Front_Load_Washers) (checked 2026-11-02) ## Int What it means: The cycle was paused or canceled; the washer may spin and drain for 20 to 30 minutes. You can usually fix this yourself. ### What to try - Press the Pause or Cancel button twice and the Power button once to remove the code. - If the code is still displayed, unplug the washer or disconnect the power for 5 minutes. Source: [Error Codes in Front Load Washers (Whirlpool Product Help)](https://producthelp.whirlpool.com/Laundry/Washers/Product_Info/Washer_Product_Assistance/Error_Codes_in_Front_Load_Washers) (checked 2026-11-02) ## rL / F34 What it means: Items were found in the drum during the Clean Washer cycle. You can usually fix this yourself. ### What to try - Remove items from the drum and restart the Clean Washer cycle. Source: [Error Codes in Front Load Washers (Whirlpool Product Help)](https://producthelp.whirlpool.com/Laundry/Washers/Product_Info/Washer_Product_Assistance/Error_Codes_in_Front_Load_Washers) (checked 2026-11-02) ## Sud / Sd What it means: Too many suds; the washer adds rinse time to break them down. You can usually fix this yourself. ### What to try - Let the washer finish its extra rinsing; the pauses are normal. - Use HE detergent in the right amount. Source: [Error Codes in Front Load Washers (Whirlpool Product Help)](https://producthelp.whirlpool.com/Laundry/Washers/Product_Info/Washer_Product_Assistance/Error_Codes_in_Front_Load_Washers) (checked 2026-11-02) ## F5 E2 What it means: The door is not locking. You can usually fix this yourself. ### What to try - Make sure nothing is caught in the door and it shuts fully. - Press Pause/Cancel twice, then Power once, to clear the code. Source: [Error Codes in Front Load Washers (Whirlpool Product Help)](https://producthelp.whirlpool.com/Laundry/Washers/Product_Info/Washer_Product_Assistance/Error_Codes_in_Front_Load_Washers) (checked 2026-11-02) ## F7 E1 What it means: The motor cannot reach the right speed. You can usually fix this yourself. ### What to try - Check that all the shipping bolts have been removed. - Check that the washer has not been overloaded. - Press the Pause or Cancel button twice and the Power button once to clear the code. Source: [Error Codes in Front Load Washers (Whirlpool Product Help)](https://producthelp.whirlpool.com/Laundry/Washers/Product_Info/Washer_Product_Assistance/Error_Codes_in_Front_Load_Washers) (checked 2026-11-02) ## F8 E1 / LO FL What it means: The washer is getting too little water. You can usually fix this yourself. ### What to try - Turn the house water on and open both hot and cold taps fully. - Check the fill hoses for kinks. - Do not use anti-flood hoses or devices in the supply line. Source: [Error Codes in Front Load Washers (Whirlpool Product Help)](https://producthelp.whirlpool.com/Laundry/Washers/Product_Info/Washer_Product_Assistance/Error_Codes_in_Front_Load_Washers) (checked 2026-11-02) ## F8 E2 What it means: Problem with the dispenser system (select models). You can usually fix this yourself. ### What to try - Check that the detergent drawer or cartridge is not clogged and clean it. Source: [Error Codes in Front Load Washers (Whirlpool Product Help)](https://producthelp.whirlpool.com/Laundry/Washers/Product_Info/Washer_Product_Assistance/Error_Codes_in_Front_Load_Washers) (checked 2026-11-02) ## F9 E1 What it means: Draining is taking longer than expected (usually over 8 minutes). You can usually fix this yourself. ### What to try - Make sure the drain hose is not kinked or clogged, and use the U-shaped drain hose form. - The drainpipe height must be between 39" (minimum) and 96" (maximum). - Excessive suds can also delay draining; make sure you are using HE detergent. Source: [Error Codes in Front Load Washers (Whirlpool Product Help)](https://producthelp.whirlpool.com/Laundry/Washers/Product_Info/Washer_Product_Assistance/Error_Codes_in_Front_Load_Washers) (checked 2026-11-02) ## Other F# E# What it means: Any other F/E fault code. This one often needs a licensed technician. ### What to try - Unplug the washer or disconnect the power for 5 minutes and reconnect it. - Reselect the cycle and press Start. - If the code persists, schedule service so a qualified technician can diagnose the washer. Source: [Error Codes in Front Load Washers (Whirlpool Product Help)](https://producthelp.whirlpool.com/Laundry/Washers/Product_Info/Washer_Product_Assistance/Error_Codes_in_Front_Load_Washers) (checked 2026-11-02) ## HC on Maytag top-load HE washers What it means: The hot and cold inlet hoses are reversed. You can usually fix this yourself. ### What to try - Turn off the water supply and reverse the hoses. - Run another cycle to verify the hoses are correct. Source: [Error Codes in Top Load HE Washers (Maytag Product Help)](https://producthelp.maytag.com/Laundry/Washers/Product_Info/Washer_Product_Assistance/Error_Codes_in_Top_Load_HE_Washers) (checked 2026-11-02) ## LdL on Maytag top-load HE washers What it means: The lid will not lock. You can usually fix this yourself. ### What to try - Check for items directly under the lid that keep it from locking. - Check for detergent build-up around the lid lock mechanism. Source: [Error Codes in Top Load HE Washers (Maytag Product Help)](https://producthelp.maytag.com/Laundry/Washers/Product_Info/Washer_Product_Assistance/Error_Codes_in_Top_Load_HE_Washers) (checked 2026-11-02) ## LdU on Maytag top-load HE washers What it means: Objects on the washer lid are preventing it from unlocking. You can usually fix this yourself. ### What to try - Take objects such as a laundry basket off the lid. Source: [Error Codes in Top Load HE Washers (Maytag Product Help)](https://producthelp.maytag.com/Laundry/Washers/Product_Info/Washer_Product_Assistance/Error_Codes_in_Top_Load_HE_Washers) (checked 2026-11-02) ## LF / Lo FL / F8 E1 on Maytag top-load HE washers What it means: The washer is taking too long to fill. You can usually fix this yourself. ### What to try - Turn on the house water and open both hot and cold taps fully; the washer needs both. Source: [Error Codes in Top Load HE Washers (Maytag Product Help)](https://producthelp.maytag.com/Laundry/Washers/Product_Info/Washer_Product_Assistance/Error_Codes_in_Top_Load_HE_Washers) (checked 2026-11-02) ## lid on Maytag top-load HE washers What it means: The lid was left open. You can usually fix this yourself. ### What to try - Close the lid. If it stays open over 10 minutes the cycle resets and drains; start again without adding more detergent. Source: [Error Codes in Top Load HE Washers (Maytag Product Help)](https://producthelp.maytag.com/Laundry/Washers/Product_Info/Washer_Product_Assistance/Error_Codes_in_Top_Load_HE_Washers) (checked 2026-11-02) ## Ofb on Maytag top-load HE washers What it means: The load is out of balance and the washer is trying to correct it. You can usually fix this yourself. ### What to try - Allow the washer to continue. - If the dial is flashing and the washer has stopped, redistribute the load, close the lid and press Start/Pause. Source: [Error Codes in Top Load HE Washers (Maytag Product Help)](https://producthelp.maytag.com/Laundry/Washers/Product_Info/Washer_Product_Assistance/Error_Codes_in_Top_Load_HE_Washers) (checked 2026-11-02) ## OL on Maytag top-load HE washers What it means: The load is too large; the washer drained the water. You can usually fix this yourself. ### What to try - Take out some items, add HE detergent, close the lid and press Start/Pause. Source: [Error Codes in Top Load HE Washers (Maytag Product Help)](https://producthelp.maytag.com/Laundry/Washers/Product_Info/Washer_Product_Assistance/Error_Codes_in_Top_Load_HE_Washers) (checked 2026-11-02) ## PF on Maytag top-load HE washers What it means: A power failure interrupted the cycle. You can usually fix this yourself. ### What to try - Press and hold Start to resume, or press Power to clear the display. Source: [Error Codes in Top Load HE Washers (Maytag Product Help)](https://producthelp.maytag.com/Laundry/Washers/Product_Info/Washer_Product_Assistance/Error_Codes_in_Top_Load_HE_Washers) (checked 2026-11-02) ## Sud on Maytag top-load HE washers What it means: Too many suds in the washer. You can usually fix this yourself. ### What to try - Always use HE (high-efficiency) detergent. Source: [Error Codes in Top Load HE Washers (Maytag Product Help)](https://producthelp.maytag.com/Laundry/Washers/Product_Info/Washer_Product_Assistance/Error_Codes_in_Top_Load_HE_Washers) (checked 2026-11-02) ## F# E# / F## on Maytag top-load HE washers What it means: A system error code. This one often needs a licensed technician. ### What to try - Press Start/Pause once to clear, then again to restart. - If it will not clear, schedule service. Source: [Error Codes in Top Load HE Washers (Maytag Product Help)](https://producthelp.maytag.com/Laundry/Washers/Product_Info/Washer_Product_Assistance/Error_Codes_in_Top_Load_HE_Washers) (checked 2026-11-02) ### Sources - [Error Codes in Front Load Washers (Whirlpool Product Help)](https://producthelp.whirlpool.com/Laundry/Washers/Product_Info/Washer_Product_Assistance/Error_Codes_in_Front_Load_Washers) (checked 2026-11-02) - [Error Codes in Top Load HE Washers (Maytag Product Help)](https://producthelp.maytag.com/Laundry/Washers/Product_Info/Washer_Product_Assistance/Error_Codes_in_Top_Load_HE_Washers) (checked 2026-11-02) Brand names and model names are trademarks of their owners. Costolio is not affiliated with or endorsed by any manufacturer. ## Related - [Whirlpool dishwashers and KitchenAid dishwashers error codes](https://costolio.com/home/appliances/whirlpool/whirlpool-dishwashers/) - [Samsung washers error codes](https://costolio.com/home/appliances/samsung/samsung-washers/) - [Whirlpool bottom-freezer refrigerators error codes](https://costolio.com/home/appliances/whirlpool/whirlpool-bottom-freezer-refrigerators/) - [LG washers error codes](https://costolio.com/home/appliances/lg/lg-washers/) - [GE washers error codes](https://costolio.com/home/appliances/ge/ge-washers/) - [Whirlpool ranges and ovens error codes](https://costolio.com/home/appliances/whirlpool/whirlpool-ranges-and-ovens/) - [All appliance error codes](https://costolio.com/home/appliances/)